How To Set Up A Wireless Router

Posted on: April 12, 2020, by :

Setting up a wireless router doesn’t have to be an ordeal. And whilst router manufacturers ought to be commended for making it less difficult to install their products, these suggestions will make the manner even simpler. I’ll also show you how to make sure your property network is as steady as it could be, and I’ll explain a few networking details that consumer manuals frequently gloss over.

The majority of router manufacturers now provide phone and pill apps that you could use for first-time set up and next tweaking. In fact, some organizations no longer hassle with browser-based totally person interfaces at all. I assume it’s great to have both options so you can decide which technique is excellent (personally, I prefer the usage of the browser due to the fact the display linked to my PC is larger and less complicated to see).

Step 1: Place Your Wireless Router

As any router manufacturer will tell you, the best place to locate your wireless router is in an open area in the center of your home. It’s great advice, because it will provide the most even coverage. It’s also impossible for most people to do, because you need to connect your router to the broadband gateway your Internet service provider (ISP) has provided you with. That equipment (be it a cable or DSL modem or—if you’re really lucky—a fiber gateway) is invariably installed at a perimeter wall.

The best place to locate your router is in the center of your home. There just happens to be a wet bar at the center of my home.

If you can’t put your wireless router in the center of your home, at least try to avoid putting in a closet that will crimp its range. You don’t need to move the gateway, but you can use a longer (and very inexpensive) CAT5e or CAT6 cable to connect the router to the gateway’s ethernet port so you can put it out in the open. If you’re really ambitious, you could run a pair of ethernet cables through your walls to that ideal central location (one cable to connect the router to your gateway, and a second to connect it to an ethernet switch—perhaps in the closet with the gateway).

But there’s also an easier option: the mesh-style router. In this system, you locate one node wherever your gateway is, and then place subsequent nodes in different rooms of your home. Your data will wirelessly hop from one node to the next, and you’ll have a strong Wi-Fi signal nearly everywhere in your house.

But, caution: Don’t put a wireless node ina Wi-Fi dead spot—it won’t be able to connect to your network any better than any client device. Instead, place the node where its wireless signalcan reach that dead spot.

Some routers have a designated WAN (Wide Area Network) port for connecting to the gateway, while others have auto-sensing ports that automatically configure themselves as WAN or LAN (Local Area Network, i.e., your home network). You’ll need to perform some preliminary steps first, so don’t disconnect or turn anything off just yet.

Many newer routers, such as the TP-Link Deco M5 show here, have auto-sensing ethernet ports that configure themselves for WAN or LAN duty based on the signal they receive from the cable.

 

Step 2: Configure your wireless router gateway

Most ISPs provide their customers with modems—aka gateways—that have routers built in. Unfortunately, these integrated modem/routers are usually of much poorer quality than stand-alone routers, and none that I know of allow you to build out mesh networks that have multiple wireless access points (or APs) that enable you to blanket your home with Wi-Fi (although Comcast will offer such a feature soon).

If your gateway has an integrated router, you’ll need to configure the gateway to disable the router and pass the WAN IP address (the unique Internet Protocol address that the ISP assigns to your account) and all network traffic through to your new router. This is necessary to avoid double-NAT scenarios, among other things. ( Here’s explanation of double NAT and why you want to avoid it.) You’ll need to know the IP address that the gateway is using (you’ll typically find this on a label on the gateway itself). Enter the IP address into a web browser to access the gateway’s configuration screen.

PCWorld If your broadband gateway also has a built-in router, such as this Motorola NVG510, you’ll need to put the gateway’s router into “bridge” or “pass through” mode to use your own router.

Some gateways have what’s known as a “bridge mode” for working with a secondary router; others handle it differently. You might need to contact your ISP for help with this step, as some won’t allow you to configure the gateway yourself.

My ISP—AT&T U-Verse—provided me with a Motorola NVG510 DSL gateway/router combo. Configuring that device to work with a router involves logging into the gateway, navigating to the Firewall menu, and setting it to “pass through mode.” You then further set the pass through mode to “DHCPS-fixed” and provide your router’s MAC (Media Access Control) address.

DHCPS is an acronym for Dynamic Host Configuration Protocol Server, which dynamically assigns IP address to the devices on your network (I’ll go into more detail on this in a bit). The MAC address is a unique identifier for router—no two are alike. Once again, the process for your gateway could be different, but the result will be the same. You’ll also need to find the setting that turns off your gateway’s Wi-Fi access point, so that you’re not running a second—and useless—Wi-Fi network. When you’ve finished making these changes, reboot your gateway.

Michael Brown/PCWorld The Motorola NVG510 is a DSL modem that AT&T sometimes provides its U-Verse broadband customers. It has a broadband connector, a phone jack for internet phone service, and a four-port ethernet switch.

Read More: Step-by-step Guide to Configure and Setup Home or Office Routers

graphics design training in lagos

We have over 15,628 DOWNLOAD of this E-Book on our site from different individual in IT Field and Discipline. Discover how we can help you too. 

Fill the form below and Get this E-Book for FREE.

Step 3: Connect your gateway to your new router

Turn off your gateway (unplug the power supply if there’s no on/off switch). If an ethernet cable is plugged into the gateway’s LAN port, unplug it and plug it into your router’s WAN port (once again, some routers have dedicated WAN and LAN ports; others have auto-sensing ports). If there is no ethernet cable plugged into the gateway’s LAN port, an ethernet cable should have come with your router. Use it to connect the gateway to your router. Turn your gateway back on and wait a minute or two for it to boot up. Next, plug in your router’s power supply and turn it on. Wait another minute or two for it to boot.

Connect your gateway to your router’s WAN port using a CAT5e or CAT6 cable (the gray cable in this photo). The red cable goes from the router to a PC, while the thinner cable plugged into the green port on the gateway connects to a phone jack in the wall..

 

Step 4: Change your wireless router’s admin password

Many router manufacturers provide smartphone apps for configuring their routers. Use it if your new router has one (in some cases, that might be the only way you can configure the router). If there’s no app, or if you’d prefer to use the router’s browser-based user interface, connect your PC to the router using an ethernet cable. Type the router’s IP address in your web browser’s address window and hit the Enter key. The router’s IP address might be printed on the router itself; it will look like 192.168.1.1 or something similar.

You’ll need the router’s admin login and password to log into it. This information might be printed on the router itself, but you might also find it in the user manual. Enter the required credentials and hit Enter. You should immediately change the default admin password because it’s not secure. Create something unique and either write it down or enter it into a password manager program such as Last Pass. You will need it later to make changes and updates. If you forget the admin password, you’ll need to perform a hardware reset, and that could undo any customization you’ve made.

 

Step 5: Update the router’s firmware

Router manufacturers often release new firmware after they’ve shipped the router. The new firmware might contain critical bug fixes as well as security and performance improvements, so always make sure you have the latest version. Most routers will check for new firmware, but few of them do this automatically—you typically need to at least click a button on the router’s configuration app. Take a look at your router’s documentation for details. You’ll need to reboot the router after a firmware update.

The first steps you should take when configuring your router is to change the admin password and update its firmware to the latest version available.

 

Step 6: Establish a password for your Wi-Fi network

Some routers come from the factory with a pre-assigned Wi-Fi password (they might even put it on a label on the router itself). Many others will at least prompt you to create one when you first set the router up. Be sure to configure the router to use at least WPA2 (second generation Wi-Fi Protected Access) encryption. The much older WEP (Wired Equivalent Password) is absolutely insecure and should not be used. No recent vintage router will use it by default, but most still support it in case you have legacy devices that can only use WEP. If you’re still using wireless devices that fall in that category, you should retire them because they’re leaving your entire network vulnerable to the most casual hacker.

The process for setting your router’s Wi-Fi password will vary from one model to the next. On the Linksys WRT1900AC router I use, for example, the settings reside in both the Connectivity and Wireless tabs (but not the Security tab, which is where you might expect them to be). If you have a dual-band router, you’ll need to assign passwords for both your 2.4GHz and 5GHz networks. They can be different passwords, but you’ll be happier if you use the same password for each (and you won’t be any more secure if you make them different). The password should be relatively complex and include letters, numbers, and special characters. Here again, you’ll find a password manager to be extremely useful unless you have a very good memory. If you operate one or more guest networks, you’ll need to create a password for those as well.

 

Step 7: Enjoy your Wi-Fi network!

If everything went according to plan, you should be able to log onto your new Wi-Fi network using the Wi-Fi password you just created. If your router has a guest network, take full advantage of it: These usually allow your guests to access the internet while walling them off from the rest of your network and the computers and storage devices connected to it.

Read More: Common And Useful Show Commands For Cisco Devices

2 thoughts on “How To Set Up A Wireless Router

Leave a Reply

Your email address will not be published. Required fields are marked *