Basic Switch Configuration Guide with Examples

Posted on: April 11, 2020, by :

This guild explains primary switch configuration instructions in detail with examples. Configuration and instructions explained on this educational are essential instructions to control a Cisco switch effectively. Learn a way to configure and control a Cisco Switch grade by grade with this basic switch instructions and configuration manual.

To explain simple transfer configuration commands, I will use packet tracer network simulator software program. You can use any network simulator software program or can use a actual Cisco transfer to observe this guide. There is not any difference in output as long as your selected software program incorporates the commands explained on this tutorial.

Create a practice lab as proven in following figure or down load this pre-created exercise lab and load in packet tracer

Download exercise topology for primary transfer configuration

If require, you could down load the brand new as properly as in advance version of Packet Tracer from here. Download Packet Tracer

In this topology

  • Two 2960 Series switches are used.
  • Switch1 (Interfarce Gig1/1) is connected with Switch2 (Interface Gig1/1) via cross cable.
  • Switch1 has two PCs connected on interfaces Eth0/1 and Eth0/2 via straight through cable.
  • Same as switch1, Switch2 also has two PCs connected on its interfaces Eth0/1 and Eth0/2.
  • IP address is configured on all PCs PC0 (192.168.1.1/24), PC1 (192.168.1.2/24), PC2 (192.168.1.3/24), PC3 (192.168.1.4/24).

Click Switch1 and click CLI menu item and press Enter Key

Navigating between different switch command modes
Cisco switches run on proprietary OS known as Cisco IOS. IOS is a group of commands used for monitoring, configuring and maintaining cisco devices. For security and easy administration, IOS commands are divided in the set of different command modes. Each command mode has its own set of commands. Which commands are available to use, depend upon the mode we are in.

Following table lists necessary commands to navigate between different IOS modes with examples.

Read More: 5 Basic Switch Settings You Must Know

Mode Purpose Prompt Command to enter Command to exit User EXEC Allow you to connect with remote devices, perform basic tests, temporary change terminal setting and list system information Router > Default mode after booting. Login with password, if configured. Use exit command Privileged EXEC Allow you to set operating parameters.

It also includes high level testing and list commands like show, copy and debug. Router # Use enable command from user exec mode Use exit command Global Configuration Contain commands those affect the entire system Router(config)# Use configure terminal command from privileged exec mode Use exit command Interface Configuration Contain commands those modify the operation of an interface Router(config-if)# Use interface type number command from global configuration mode Use exit command to return in global configuration mode Sub-Interface Configuration Configure or modify the virtual interface created from physical interface Router(config-subif) Use interface type sub interface number command from global configuration mode or interface configure mode Use exit to return in previous mode. Use end command to return in privileged exec mode.

Setup Used by router to create initial configuration, if running configuration is not present Parameter[Parameter value]: Router will automatically insert in this mode if running configuration is not present Press CTRL+Cto abort. Type Yesto save configuration, or Noto exit without saving when asked in the end of setup. ROMMON If router automatically enter in this mode, then it indicates that it fails to locate a valid IOS image. Manual entrance in this mode Allow you to perform low-level diagnostics. ROMMON> Enter reload command from privileged exec mode. Press CTRL + Ckey combination during the first 60 seconds of booting process Use exit command. How to get help on Cisco Switch command mode
Switch provides two types of context sensitive help, word help and command syntax help.

Command Syntax Help

Command syntax help can be used to get the list of keyword, commands, or parameters that are available starting with the keywords that we had already entered. Enter ?(Question mark) after hitting Space key and prompt will return with the list of available command options. For example to know the parameters required by show ip command type show ip ?and prompt will return with all associate parameters. If prompt returns with only as an option, that means switch does not need any additional parameters to complete the command. You can execute the command in current condition.

graphics design training in lagos

We have over 15,628 DOWNLOAD of this E-Book on our site from different individual in IT Field and Discipline. Discover how we can help you too. 

Fill the form below and Get this E-Book for FREE.

How to set name on switch

Switch name can be set from global configuration mode. Use hostname [ desired hostname]command to set name on switch.

 

How to set password on a Catalyst switch

Passwords are used to restrict physical access to switch. Cisco switch supports console line for local login and VTYs for remote login. All supported lines need be secure for User Exec mode. For example if you have secured VTYs line leaving console line unsecure, an intruder can take advantage of this situation in connecting with device. Once you are connected with device, all remaining authentication are same. No separate configuration is required for further modes.

Password can be set from their respective line mode. Enter in line mode from global configuration mode.

VTY term stand for virtual terminal such as telnet or SSH. Switch may support up to thousand VTYs lines. By default first five (0 – 4) lines are enabled. If we need more lines, we have to enable them manually. 2960 Series switch supports 16 lines. We can set a separate password for each line, for that we have to specify the number of line. In our example we set a common password for all lines.

Read More: 10 Commands You Need To Know When Using The Cisco IOS

Above approach is right for small companies, in which numbers of community administrators are very few. In above approach we must percentage password between all directors. Switch supports both neighborhood and faraway server authentication. Remote server authentication is a complex method and not included in any access degree exams. For this newsletter I am additionally skipping faraway server approach. In local database authentication method switch allows us to set a separate password for each person. Two worldwide configuration commands are used to set neighborhood user database.

Switch(config)#username [Username] password[test123] Or Switch(config)#username [Username] secret[test123]

Both commands do same job. Advantage of using secret option over password option is that in secret option password is stored in MD5 encryption format while in password option password is stored in plain text format.

Along with User Exec mode we can also secure Privilege Exec mode. Two commands are available for it.

Switch(config)# enable password Privilege_EXEC_password or Switch(config)# enable secret Privilege_EXEC_password

Again as I mentioned earlier, password stored with secret command is encrypted while password stored with password command remains in plain text. You only need to use single command. If you would use both commands as I did, enable secret command would automatically replace the enable password command.

How to reset switch to factory defaults

During the practice several times we have to reset switch to factory defaults. Make sure you don’t run following commands in production environment unless you understand their effect clearly. Following commands will erase all configurations. In production environment you should always takes backup before removing configurations. In LAB environment we can skip backup process.

Switch>enable Switch#delete flash:vlan.dat Delete filename [vlan.dat]? [Press Enter Key] Delete flash:vlan.dat? [confirm] [ Reconfirm by pressing enter key] Switch#erase startup-config Switch#reload

 

How to set IP address in Switch

IP address is the address of device in network. Switch allows us to set IP address on interface level. IP address assigned on interface is used to manage that particular interface. To manage entire switch we have to assign IP address to VLAN1( Default VLAN of switch). We also have to set default gateway IP address from global configuration mode. In following example we would assign IP 172.16.10.2 255.255.255.0to VLAN1 and set default gateway to 172.16.10.1.

Switch>enable Switch#configure terminal Switch(config)#interface vlan1 Switch(config-if)#ip address 172.16.10.2 255.255.255.0 Switch(config-if)#exit Switch(config)#ip default-gateway 172.16.10.1

 

How to set interface description

Switches have several interfaces. Adding description to interface is a good habit. It may help you in finding correct interface. In following example we would add description Development VLANto interface FastEthernet 0/1.

Switch(config)#interface fastethernet 0/1 Switch(config-if)#description Development VLAN

 

How to clear mac address table

Switch stores MAC addresses in MAC address table. Gradually it could be full. Once it full, switch automatically starts removing old entries. You can also clear these tables manually from privileged exec mode. To delete all entries use following command

switch#clear mac address-table

To delete only dynamic entries use

switch#clear mac address-table dynamic

How to add static MAC address in CAM table
For security purpose sometime we have to add mac address in CAM table manually. To add static MAC address in CAM table use following command

Switch(config)#mac address-table static aaaa.aaaa.aaaa vlan 1 interface fastethernet 0/1

In above command we entered an entry for static MAC address aaaa.aaaa.aaaaassigned to FastEnternet 0/1with default VLAN1.

 

How to save running configuration in switch

Switch keeps all running configuration in RAM. All data from RAM is erased when we turned off the device. To save running configuration use following command

Switch#copy running-config startup-config

 

How to set duplex mode

Switch automatically adjust duplex mode depending upon remote device. We could change this mode with any of other supported mode. For example to force switch to use full duplex mode use

Switch(config)# #interface fastethernet 0/1 Switch(config-if)#duplex full

To use half duplex use Switch(config)# #interface fastethernet 0/1 Switch(config-if)#duplex half

 

show version

show version command provides general information about device including its model number, type of interfaces, its software version, configuration settings, location of IOS and configuration files and available memories.

show mac-address-table

Switch stores MAC address of devices those are attached with its interfaces in CAM table. We can use show mac-address-tablecommand to list all learned devices. Switch uses this table to make forward decision.

show flash

Switch stores IOS image file in flash memory. show flash command will list the content of flash memory. This command is useful to get information about IOS file and available memory space in flash.

show running-config

Configuration parameter values are created, stored, updated and deleted from running configuration. Running configuration is stored in RAM. We can use show running-config command to view the running configuration.

show startup-config

Any configuration stored in RAM is erased when devices is turned off. We can save running configuration in NVRAM. If we have saved running configuration in NVRAM, it would be automatically loaded back in RAM from NVRAM during the next boot. As switch load this configuration back in RAM in startup of device, at NVRAM it is known as startup-config.

show vlan

show vlan command will display the VLANs. For administrative purpose, switch automatically create VLAN 1 and assign all its interfaces to it. You can create custom VLANs from global configuration mode and then assign them to interfaces.

show interface

show interface command displays information about interfaces. Without argument it would list all interfaces. To get information about specific interface we need to pass its interface number as an argument. For example to view details about FastEthernet 0/1, use show interface fastethernet 0/1.

First line from output provides information about the status of interface.

FastEthernet0/1 is up, line protocol is up ( connected)

The first up indicates the status of the physical layer, and the second up indicates to the status of the data link layer.

Possible interface status

  • up and up :-Interface is operational.
  • up and down :-Its data link layer problem.
  • down and down :-Its physical layer problem.
  • Administratively down and down :-Interface is disabled with shutdown command.

Possible values for physical layer status

  • Up :-Switch is sensing physical layer signal.
  • Down :-Switch is not sensing physical layer signal. Possible reasons could be cable is not connected, wrong cable type is used and remote end device is turned off.
  • Administratively down :-Interface is disabled by using shutdown command.

Possible values for data link layer status

  • Up :-The data link layer is operational.
  • Down :-The data link layer is not operational. Possible reasons could be a disabled physical layer, missed keep alives on a serial link, no clocking or an incorrect encapsulation type.

show ip interface brief

show ip interface briefis a extremely useful command to get quick overview of all interfaces on switch. It lists their status including IP address and protocol.

Read More: Cisco Switch Troubleshooting Basics and Steps list

2 thoughts on “Basic Switch Configuration Guide with Examples

Leave a Reply

Your email address will not be published. Required fields are marked *